EPS Cement Sandwich Wall Panel Lightweight For ZJT

1.lightweight,anti-impact,resist compression .(br/) 2.brick masonry construction capacity of 12 individuals for eight hours a day,if use ZJT wall panel in construction,three people could complete in 60 minutes,so efficiency advantage is very significant.(br/)
Chat Now

Product Details

Why choose our ZJT lightweight energy-saving sandwich panel?

Answer:ZJT lightweight energy-saving composite wall panel has many advantage which light weight,compressive strength,strong impact resistance that other materials do not have in the construction of the transportation,handing ,cutting.Because wall panel using assemble design,the skill of the operation personnel is required extremely low and master coolie all can do.Compared with traditional clay brick construction,the efficiency can be promoted about 10 times,without plaster processing,greatly save the time for a project.

What are the product features?

05_wps图片.jpg

01.Lightweight 、Optimize structures

The traditional brick block, the wall must be located on the vertical position of the beam, using the Zhongjingtai wall material, can extend the spacing between beams and columns, the wall body can not be limited by the beam column, and the economic efficiency is prominent.


开槽布线8.jpg

02.Strong hanging force,can be slotted wiring and buried pipe

By hanging test,the single point hanging force of wall panel can be up to 50kg and above level,and fully meet the wall of the general bearing applications,such as the installation of air-conditioning,condole ark,water heater,fixed,marble mesa skeleton support and so on.


HTB1m7kiFVXXXXXwXVXXq6xXFXXXO.jpg03.Sound insulation

ZJT lightweight sandwich panels have good sound insulation,it is 40db for 90mm thick wall and much better for thicker panels,the sound effects in the line with national residential sound requirements,much higher than other excuses brick wall of sound effects.


与传统砖墙比较.jpg

04.Easy to construct,Transport and time saving

text some content here.text some content here.text some content here.text brick masonry construction capacity of 12 individuals for eight hours a day,if use ZJT wall panel in construction,three people could complete in 60 minutes,so efficiency advantage is very significant.


Where are the advantages?


A-PANEL13_wps图片.jpg

Enveronment Friendly


防火.jpg

Fireproof


抗震.jpg

Anti-Earthquake


eps-sandwich-panel-house_wps图片.jpg

Solid Core


产品成品图.jpg

High Stability


16_wps图片.jpg

Performance Stability


Where are the product applications?

1).Interior partition (60mm,75mm or 90mm is your best choice)

2).Exterior Wall (100mm,120mmor 150mm)

3).Floor and roof

4).prefabricated houses

5).Modern high-rise Building

6).Schools, Hotels, office

7).Indoor space of ecological residences

8).All kinds of houses and structures


墙板应用大全


How to install?


Alignment:making the base line of the installation position of the wallboard.

       ↓

Sawing of wallboard:cutting and adjusting the width and length of wallboard on the basis of the requirement.

       ↓

Sizing: blending the ZJT cement mortar and plastering it into the gap and base line bettwen the wallboard.

       ↓

Fitting the sheet: moving the mortar-covered wallboard to the right position and using crowbar to ensure the wallboard are tight with another one.

       ↓

Placing the wallboard: filling the vacant position of the wall 

       ↓

Adjustment: fixing the wallboard with wooden wedge, spiking steel bar into the glued wallboard an two steel bars should be spiked beyong 120mm wall board.

       ↓ 

Filling joints: clear away the facial panel  cement mortar and press it tightly with round steel bar.

       ↓

Installation of crack-resistant material: after about one week, taking out the wooden wedges and paste the anti-crack tape with cement mortar.

       ↓

Insertion of wires: do not dig the same place in the two wallboard facial and the deep can't beyond 2/3 of the wallboard.

       ↓

Plastering paint: to finish the wal, tiles can be paste without any scraping and wallpaper also can be applied directly.

安装图解2


FAQ

1. What is your mainly products?

    Our mainly products are sandwich wall panel and  color steel panel .

2. What is your delivery time?

    One 20'GP container, about 10 working days

3. How about the samples?

   The samples is free, but the delivery cost will be on ur account, and we will deduct it after you place the order.

4. What is your time of making samples?

     Usually we will take 1~3 days to make the sample.

5.  What is your payment terms?

     Normally we accept 30% T/T in advance,70% after shipment.

     Or Irrevocable L/C

6. What is the shipping port?

     Xiamen port


Contact

Fuma_MimePart_5

Xiamen Zhongjingtai Building Materials Co., Ltd 

Unit2A, Lianchang Building, No6-8 Huli District, Xiamen, China 

Contact person:Jodie Huang  

TEL: +86-592-5216902    FAX: +86-592-5216319    

Mobile/Whatsapp/Wechat: +86 13695041249                      

Email: sales07@zhongjingtai.com   Website: www.zhongjingtai.com  






Inquiry